Furnace Not Heating AC Tool Pro
Gas furnace troubleshooting

Furnace not heating? Start here.

Most no-heat calls come down to a handful of things. Run the safe homeowner checks first — some of them are free fixes. If those don't do it, the technician section walks through the sequence of operation step by step.

Smell gas? Stop. Don't flip switches or try to relight anything. Get everyone out of the house and call your gas company or 911 from outside. If your carbon monoxide alarm is going off, get out and call 911.

Furnace Not Working? What to Check Before You Call a Tech (And What Techs Check Next)

Homeowner checks (safe to do yourself)

Go in this order. Stop when the heat comes back.

  • Thermostat. Set to HEAT (not COOL or OFF), set a few degrees above room temperature, and replace the batteries if the screen is dim or blank.
  • Air filter. A clogged filter makes the furnace overheat and shut the burners off on the high limit. Replace it — this fixes more no-heat calls than anything.
  • Power. Check the light-style switch on or near the furnace and the furnace breaker in your panel.
  • Front panel. The furnace has a door safety switch. If the bottom door isn't pushed in all the way, the furnace won't run.
  • Gas supply. Make sure the gas valve to the furnace is on. On propane, check that the tank isn't empty. If other gas appliances don't work either, call your gas supplier.
  • Vent pipes (high-efficiency furnaces). If your furnace has white PVC pipes going outside, make sure snow, ice, leaves or a nest aren't blocking them.
  • Condensate drain (high-efficiency furnaces). A clogged drain or full condensate pump can stop the furnace. Look for water in the trap or around the unit.
  • Blinking light. Look through the little window on the furnace door. Write down the flash pattern and match it to the chart on the door before you turn the power off — then tell your tech the code.

Still no heat? Call a licensed HVAC technician. Gas and high voltage aren't something to experiment with — but now you can tell them exactly what you already checked.

Technician diagnosis: follow the sequence

Every induced-draft gas furnace follows the same basic sequence. Find the step where it stops, and you've found your problem. Always confirm against the manufacturer's wiring diagram and specs.

1

Call for heat

Verify 24V on W from the thermostat. No W? Look at the thermostat, wire, transformer and the low-voltage fuse on the board.

2

Inducer starts

Board energizes the inducer. Inducer not running: check voltage to the motor, then the motor and its capacitor if it has one.

3

Pressure switch closes

Inducer runs but pressure switch stays open: check the hose and port, a clogged drain/trap, a blocked vent or intake, then the switch itself with a manometer.

4

Igniter heats

No glow: check voltage at the hot surface igniter, then its resistance. Cracked or open igniters are common failures.

5

Gas valve opens

Igniter glows but no flame: put your meter on the valve during trial for ignition. 24V and no gas = bad valve. No 24V = look upstream at the board or a safety.

6

Flame proven

Lights then shuts off in a few seconds: the board isn't proving flame. Clean the flame sensor, check microamps and burner ground.

7

Blower on

Burners run, then shut down on a limit: airflow problem. Filter, blower wheel, motor/capacitor, closed registers, undersized duct.

8

Gas pressure

Flames lifting, rolling or dropping out: verify inlet and manifold pressure with a manometer and set it to the nameplate spec.

⚡

Faster with the app

AC Tool Pro's Diagnose mode walks you through heating calls step by step on your phone. Try it →

Watch the fixes

Real furnace calls, start to finish.

Why Your Furnace Is Running but Not Heating (Pressure Switch Issues)

Furnace Not Heating? Gas Valve or Control Board — Here's How I Know

Gas Furnace Turning Off? Here's What Might Be Happening

How to Check the Flame Sensor

Gas Valve Troubleshooting Secrets Beginner HVAC Technicians Need

Gas Furnace Flames Keep Going Out? This Is Why

Furnace Tune Up: How I Clean, Test & Set Gas Pressure

Gas Furnace Pilot Light Won't Stay Lit? Fix It Now!

Tools for the job

For techs who want the whole picture.

App

AC Tool Pro

Diagnose in heating or cooling mode, PT charts, airflow and BTU calculators, and a 3D view of every component. Used by 200+ techs.

$20/mo or $200/yr
Get the app
Video course

Mini Split Training

My full mini split course — how they work, maintenance, repair, sizing and install. 45 videos, quizzes and a certificate.

$49.99/mo or $299/yr
Start the course
Membership

Taddy Digest Members

Members-only HVAC training courses on YouTube — deeper, longer videos you won't find on the public channel.

Join on YouTube

More heating videos: HVAC Training Videos — Gas Furnaces · Comparing systems? Heat pump vs gas furnace

Who's teaching this?

I'm Taddy — a licensed mechanical contractor in Tennessee with 20 years in the field. I run Fuller Heating and Cooling and the Taddy Digest YouTube channel, where 250,000+ techs, students and homeowners learn HVAC and solar from real jobs, not textbooks. I'll keep you cool if you let me.

Furnace not heating — common questions

Why is my furnace running but not heating?

If the blower runs but the air is cold, the burners usually aren't lighting or aren't staying lit. Common causes are a dirty filter tripping the high limit, a pressure switch that won't close (often a clogged condensate drain or blocked vent on a 90% furnace), a failed hot surface igniter, or a dirty flame sensor.

Why does my furnace turn on then shut off?

Short cycling on a gas furnace is often a dirty flame sensor (the burners light, then shut off within seconds), an overheating limit switch caused by a dirty filter or poor airflow, or a pressure switch dropping out. The blinking light on the control board usually tells you which.

What should I check before calling a technician?

Make sure the thermostat is on HEAT and set above room temperature, replace the filter, confirm the furnace switch and breaker are on, make sure the front panel is fully seated, check that the gas is on (or the propane tank isn't empty), and clear snow or debris from the outdoor intake and exhaust pipes.

Is it safe to work on my own gas furnace?

Simple checks like the thermostat, filter and power switch are safe for homeowners. Anything involving gas valves, gas pressure, burners or wiring should be done by a trained technician. If you smell gas, leave the house and call your gas company from outside.

What do the blinking lights on my furnace mean?

The LED on the control board flashes a code that points to the problem — for example a pressure switch, limit or flame fault. The code chart is usually printed on the inside of the furnace door. Write the code down before you turn the power off, because cycling power can clear it.